{"product_id":"conductive-mesh-eld-stainless-steel-roll","title":"Conductive Mesh for Electronic Leak Detection — ConDuct™ Stainless Steel, 1,800 SF Roll","description":"\u003cp\u003e\u003cstrong\u003eConductive mesh\u003c\/strong\u003e gives a roofing or waterproofing assembly the electrical reference that Electronic Leak Detection needs. Laid between the insulation and the cover board, it creates a continuous conductive plane across the roof so low-voltage and high-voltage testing can locate a breach anywhere in the membrane.\u003c\/p\u003e\u003cp\u003eSupplied as ConDuct™ Stainless Steel Mesh, open-net style, in 1,800 square foot rolls.\u003c\/p\u003e\u003ch3\u003eWhen a conductive mesh is required\u003c\/h3\u003e\u003cp\u003eSpecify conductive mesh when:\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003eThere is no other suitable electrical reference available for high-voltage or low-voltage manual leak detection, or\u003c\/li\u003e\n\u003cli\u003eThe assembly is being built so a permanent always-on leak detection system can be installed or retrofitted later.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhere it goes in the assembly\u003c\/h3\u003e\u003cp\u003eBottom to top: roof deck, optional vapour barrier, optional insulation, \u003cstrong\u003econductive mesh\u003c\/strong\u003e, cover board, membrane.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstall the mesh between the insulation and the cover board. Do not install it directly beneath the membrane\u003c\/strong\u003e unless both the membrane manufacturer and the leak detection provider have approved it. This is the most common installation error and it compromises the test.\u003c\/p\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaterial:\u003c\/strong\u003e 304 stainless steel\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRoll size:\u003c\/strong\u003e 72 in wide × 300 ft long — 1,800 SF gross per roll\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMesh opening:\u003c\/strong\u003e 3\/4 in nominal (19 mm × 20 mm)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWire diameter:\u003c\/strong\u003e 0.016 in (0.412 mm) — ASTM B-557\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTensile strength:\u003c\/strong\u003e 260 ksi — ASTM A-313\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eElongation:\u003c\/strong\u003e 1–10% — ASTM B-557\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWind type:\u003c\/strong\u003e normal \/ reverse\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eVolume pricing\u003c\/h3\u003e\u003ctable\u003e\n\u003ctr\u003e\n\u003cth\u003eSquare feet\u003c\/th\u003e\n\u003cth\u003eRolls\u003c\/th\u003e\n\u003cth\u003ePer SF\u003c\/th\u003e\n\u003cth\u003ePer roll\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eup to 25,000\u003c\/td\u003e\n\u003ctd\u003e1–13\u003c\/td\u003e\n\u003ctd\u003e$0.80\u003c\/td\u003e\n\u003ctd\u003e$1,440\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e25,001–50,000\u003c\/td\u003e\n\u003ctd\u003e14–27\u003c\/td\u003e\n\u003ctd\u003e$0.78\u003c\/td\u003e\n\u003ctd\u003e$1,404\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e50,001–75,000\u003c\/td\u003e\n\u003ctd\u003e28–41\u003c\/td\u003e\n\u003ctd\u003e$0.75\u003c\/td\u003e\n\u003ctd\u003e$1,350\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e75,001–150,000\u003c\/td\u003e\n\u003ctd\u003e42–83\u003c\/td\u003e\n\u003ctd\u003e$0.72\u003c\/td\u003e\n\u003ctd\u003e$1,296\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e150,001+\u003c\/td\u003e\n\u003ctd\u003e84+\u003c\/td\u003e\n\u003ctd\u003e$0.68\u003c\/td\u003e\n\u003ctd\u003e$1,224\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/table\u003e\u003cp\u003ePricing applies automatically at checkout based on the number of rolls in your order.\u003c\/p\u003e\u003ch3\u003eOrdering — read before you calculate\u003c\/h3\u003e\u003cp\u003eThe 1,800 SF figure is gross. Adjacent runs must overlap a \u003cstrong\u003eminimum of 2 inches\u003c\/strong\u003e at side and end laps, so usable coverage is lower — and lower again on a roof with penetrations, curbs or changes in plane. Order to your laid-out area, not to the gross roll figure.\u003c\/p\u003e\u003ch3\u003eHandling and cutting\u003c\/h3\u003e\u003cp\u003eCut and loose wire ends are sharp. \u003cstrong\u003eGloves and eye protection are required.\u003c\/strong\u003e The mesh is tough enough to dull standard metal shears quickly — a small circular grinding wheel cuts it cleanly and quickly. Follow standard grinder safety procedure.\u003c\/p\u003e\u003ch3\u003eTerminating the mesh\u003c\/h3\u003e\u003cp\u003eA mesh installation needs a connection point so test equipment can be attached without disturbing the roof. See our \u003ca href=\"\/products\/eld-connection-plate-kit\"\u003eELD Connection Plate Kit\u003c\/a\u003e.\u003c\/p\u003e\u003ch3\u003eSpecification and installation documents\u003c\/h3\u003e\u003cp\u003eA three-part CSI specification — \u003cstrong\u003eSection 07 01 91, Conductive Mesh for Roofing and Waterproofing Leak Detection\u003c\/strong\u003e — and our installation guidance are available on request. Prices exclude freight; see below.\u003c\/p\u003e\u003ch3\u003eFreight\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003ePrices exclude freight.\u003c\/strong\u003e These are heavy goods and shipping is quoted per order based on weight, quantity and destination. Place your order and we will confirm freight before shipment.\u003c\/p\u003e","brand":"Atlantic Testing Services","offers":[{"title":"1,800 SF Roll (72 in × 300 ft)","offer_id":48954827440282,"sku":"ATS-MESH-1800","price":1440.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0765\/4896\/4506\/files\/mesh-roll-end2better.png?v=1785888223","url":"https:\/\/conductivemediums.com\/products\/conductive-mesh-eld-stainless-steel-roll","provider":"Conductive Mediums - Mesh and Primer","version":"1.0","type":"link"}